| |
Please note: the Telstra self
install kit does not support the following setup. Hence, modems set back
to factory default settings will destroy the settings below.
In its current configuration set up
for BigPond, the SpeedStream modem is not set up to host other servers
on the user LAN side. To enable this feature, the PPPoE termination will
need to be on the PC rather than the modem.
Instructions for making the necessary
changes are set out below:
6520 Modem set-up:
- Reset the modem
to its factory default settings
- Type the
modem’s URL into the Internet browser (address bar
in Internet Explorer), Note: You need to determine
the DHCP address for the modem. For Windows 2000 or
XP, this can be performed by:
• Select
“Run” from the “Start” menu
• Type “cmd”,
then enter
• At the DOS
prompt, type “ipconfig/all”, then enter
• Note the
DHCP server address; this is the modem address
- You will be
prompted for your ISP username and password. Also,
you need to select your preferred connection mode:
•
Auto-Connect on Disconnect
• Connect on
Demand
• Dial-up
Mode
- A
“Congratulations” page will be displayed. Click
“Finish”
- Click on
“Continue”
- Type in
username: admin, password: admin. Then, click “Log
in”
- Under the
“Gateway Options”, click on the “ISP Connection”
icon
-
On
the bottom centre of the page, click “Advanced
Settings”
-
Click “Configure the ATM Virtual Circuit”
-
Under the “VC” heading, click on 8/35
-
Click “Next”
-
Select protocol “PPPoE” and then click “Next” again
-
Under PPPoE Type, select “Bridge only” and then
click “Next”
-
Click “Finish”
-
Click “Reboot”. A reboot is required before the new
configuration takes effect, so click the "Reboot"
icon, then click the additional "reboot" option that
is displayed. DO NOT select the "Reset to factory
defaults" option as this will remove all the
configuration changes that have been made.
4200 Modem set-up:
- Reset the
modem to ensure it is in default
mode (refer instructions below).
- Type the
modem's URL into the internet
browser (address bar in Internet
Explorer), Note: You need to
determine the DHCP server address
for the modem. For Windows 2000 or
XP, this can be performed by
selecting “Run” from the “Start”
menu:
• type cmd, then enter
• at the DOS prompt, type: ipconfig
/all, then enter
• note the DHCP server address. This
is the modem address.
- Click "Login"
option. The "Username" is admin and
the "Password" is admin. Then click
"OK".
- Click the
"Setup" option and then click the
"WAN interface" option.
- If asked for
a Username/Password use admin/admin
- Click under
VC heading the "8/35" option.
- Click
"Next>>"
- The PPPoE
option should be selected and then
click "Next>>" again.
- Under the
heading "PPPoE Type" select the
"Bridge only" option and then click
"Next>>".
- Click
"Finish"
- A reboot is
required before the new
configuration takes effect. Click
the word "reboot". An additional
"Reboot" button will be displayed.
Click this "Reboot" button"
PC setup for
running PPPoE (for Windows):
- Go to the
Control Panel from the Start Menu
- Click Network
Connections
- Under the
Wizard heading – click “New
Connection Wizard”
- At the
Network Connection Type screen,
click “Connect to the Internet”
- Select “Setup
my connection manually”
- Select “
Connect using a broadband connection
that requires a user name and
password”
- @ the
Connection Name Screen, type in
BigPond where it asks for the ISP
name
- @ the
Connection Availability screen
select “Anyones Use”
- @ Internet
Account Information screen, enter
your user name and details and
ensure both of the check boxes, are
ticked ie for
-
“use this
account name and password when
anyone anyone connects to the
internet from this computer”,
and
-
“make
this the default internet
connection”.
- @ the
Completion of New Connection Wizard,
tick “add a shortcut to this
connection to my desktop”.
To go online,
every time you wish to connect, double
click the BigPond icon, enter your user
name and password and click “connect”.
Resetting modem to Factory Defaults
Resetting the
modem may be required if you have
changed the modem’s settings and wish to
reset it to the factory default
configuration.
Note: Resetting the modem will wipe all
previous configurations and you will
need to re-enter your provider account
details. This can be simplified by using
the Self Installation Kit CD from your
provider.
4200 Modem
|
|
- Using the tip
of a ballpoint pen or unfolded
paperclip, press and hold the Reset
button located on the bottom of the
router. The pwr LED will blink red
once, indicating that the reset has
begun.
- Continue
depressing the Reset button for four
seconds or until the pwr LED begins
to blink alternating red-to-green.
- Release the
Reset button.
6520 Modem
- From your
internet browser go the URL of
http://10.0.0.138 (Big Pond). For
Internet Explorer you type this at
the address bar.
- Login into
the modem by clicking the "Go"
option at the top left of the screen
where it says "Log In:”
- The
"Username" is admin and the
"Password" is admin
- Click the
"Reboot" icon.
- Select the
"Reset to Factory Defaults" option
as (Note: this will remove all the
configuration changes that have been
made.)
Now click the additional "reboot"
option that is displayed.
--- |
|
|
|
|
|
